Skip to main content
$49 Heating Tune-Up · Limited time — see all promotions
Southeast Heating & Cooling logo
Mini Split

Mini-Split Installation in Buford & North Georgia

Mini-split installation for bonus rooms, additions and whole homes in Buford and nearby cities. Daikin R-32 systems. Free estimate.

Southeast technicians with a newly installed ductless mini-split

Mini-split installation adds ductless heating and cooling to a room, an addition or a whole home without running ductwork. Southeast Heating & Cooling installs Daikin R-32 mini-splits across Buford and the surrounding communities, sized with a Manual J load calculation.

What does a mini-split installation involve?

A ductless mini-split has two main pieces: an outdoor unit and one or more indoor heads. A small line set carries refrigerant between them through a hole about the size of a coffee cup, and control wiring lets the pieces talk. Each head conditions its own zone with its own temperature setting. A single-zone system serves one room; a multi-zone system runs several heads from one outdoor unit.

Installing one means choosing the right capacity for each zone, placing the heads where they'll actually move air across the room, routing the line set and condensate drain cleanly, providing a properly sized electrical circuit, and commissioning the system so it runs the way the manufacturer designed it. It's far less invasive than adding ductwork, but it is not a plug-in appliance, and the quality of the install is most of what decides how well it works for years to come.

We install Daikin's ductless lines, Daikin Entra and Oterra. Every new Daikin system we install uses R-32 refrigerant. We're a Daikin Premier Dealer, which means our installers work with this equipment week in and week out, and our technicians also service all major brands.

When does a ductless system make sense?

Mini-splits solve specific problems. They're the right call when you have:

  • A room the central system can't keep up with. The bonus room over the garage, the sunroom, the finished basement. A dedicated head fixes that room without overworking the rest of the house.
  • An addition or converted space. Stretching the existing ductwork into new square footage often means the old system is now undersized for the whole house. A mini-split gives the new space its own system.
  • A home office, in-law suite or garage workshop that needs its own temperature without heating or cooling the whole house to get it.
  • A house with no ducts at all. A home with baseboard or radiant heat can get whole-home cooling and heating from a multi-zone system.
  • Zoning you can't get from one central system. If half the household wants it cold and the other half wants it warm, per-room heads settle the argument.

Mini-splits are not the answer to everything. If your central system is the real problem, we'll tell you whether an HVAC replacement or a duct repair serves you better than adding heads. And if you're swapping out a ductless system that's already in place, our mini-split replacement page covers that situation.

What can go wrong with a mini-split install?

Most of the ductless problems we're called to repair trace back to the day the system went in. The common mistakes:

  • Wrong capacity. An oversized head short-cycles and leaves the room clammy; an undersized one runs nonstop and never catches up. Guessing by square footage is how both happen.
  • Poor head placement. A head mounted where its airflow hits a beam, a ceiling fan or a doorway conditions the hallway instead of the room.
  • Bad flare connections. The line set joins the equipment with flared copper fittings. A flare that's cut short, scored or overtightened leaks refrigerant slowly for months.
  • Skipping the vacuum. Moisture and air left in the line set damage the compressor over time. Pulling a deep vacuum and verifying it holds is not an optional step.
  • Drain problems. A condensate line with no slope, or a pump wired wrong, ends with water on the wall.
  • Undersized electrical. Each outdoor unit needs a properly sized circuit and disconnect. Tapping an existing circuit is a shortcut that trips breakers and can be a safety problem.
  • No permit, no registration. Skipping a permit when one is required can surface at sale time, and if the manufacturer warranty never gets registered, you may not have the coverage you think you have.

How does Southeast install a mini-split?

  1. Free in-home estimate. A comfort consultant walks the space with you, looks at the rooms, the walls, the electrical panel and the outdoor location, and asks what problem you're trying to solve.
  2. Manual J load calculation. That's the industry method for sizing equipment to the home. We use it on every replacement and installation project so head capacity is based on the room's actual heat gain and loss rather than a rule of thumb.
  3. A written proposal with options. Single-zone or multi-zone, which heads, where they go, and what's included. You'll see the price and the financing choices side by side. Every home is different, and the proposal is specific to yours.
  4. Permit and scheduling. Southeast pulls the required permit when one is needed, and the necessary permit cost is included in the quoted price.
  5. Installation day. Our installers mount the heads, set the outdoor unit, route and conceal the line set, run the drain with proper slope, and connect power on a properly sized circuit with a disconnect.
  6. Startup and commissioning. We pressure-test and pull a vacuum on the line set, charge the system to specification, and run every head through heating and cooling before we leave.
  7. Warranty registration and walkthrough. We register the manufacturer warranty for you and show you how the remote and the washable filters work.

If a problem is caused by our workmanship, Southeast will return and correct it at no charge. We're family owned and locally owned, licensed in Georgia (CR110452), and we've earned 1,000+ five-star Google reviews.

Curious about the sizing step? Our article on Manual J load calculations explains it in plain language, and HVAC permits and inspections in Georgia covers what the permit is for.

What does a mini-split installation cost?

We don't publish mini-split prices online, and we'd be cautious of anyone who does without seeing the house. The total depends on the capacity you need, how many heads, line-set length and routing, whether line hide is needed, electrical work, mounting, the condensate drain, and the permit. Two homes in Alpharetta with the same square footage can land in very different places.

What we can tell you: the estimate is free, and there are ways to make the project fit a monthly budget. Through Service Finance, with credit approval, we offer 18 months at 0% interest, 12 months with no payments and no interest, and 180-month terms at 9.99%; see financing terms. Our financing page has the details. We also offer up to $1,000 off a new system; some restrictions may apply, and current offers are on our promotions page.

After the install, the Southeast Family Plan keeps the system on a twice-a-year schedule, and our mini-split maintenance page explains what a ductless tune-up covers.

Want a free estimate for a ductless system?

Get a Free Replacement Estimate or call or text (770) 265-8308. We install mini-splits across Buford, Cumming, Alpharetta, Braselton and Flowery Branch and the surrounding North Georgia communities, and we'll give you a straight answer on whether ductless is the right fix for your room. See the rest of our ductless services on the mini-split page.

Frequently asked questions

Do you perform a Manual J? +
Yes. Southeast performs Manual J load calculations for replacement projects so system sizing is based on the home rather than a simple like-for-like assumption. For a mini-split, that means each head is sized to its zone's actual load.
Are permits included? +
Southeast pulls required replacement permits, and the necessary permit cost is included in the quoted installation price.
Can a mini-split heat as well as cool? +
Yes. A mini-split is a heat pump, so it cools in summer and runs in reverse to heat in winter. Cold-weather heating performance varies by model, so we go over the manufacturer's data for the specific equipment on your proposal.
Do you offer HVAC financing? +
Yes. Southeast offers Service Finance options including approved promotional programs such as 18 months at 0% interest and 12 months with no payments and no interest, subject to credit approval and current terms.
Do you register the equipment warranty? +
Yes. Southeast handles manufacturer warranty registration for systems we install.
Which Daikin mini-split lines do you install? +
Daikin Entra and Oterra. Both are ductless lines, separate from Daikin's central single-stage, two-stage and Fit systems. We go through the current Daikin specifications for the sizes and configurations that fit your home at the free estimate.

Ready to get comfortable again?

Book your service online, or call now for emergency help. Our Buford-based team is ready when you are.